Safety first: gas smell means leave
Gas appliances are not a place for guessing.
If you smell gas
Leave the house, do not use switches or phones inside, and call your gas utility or 911 from outside.
Do not relight repeatedly
Repeated attempts can build up gas around the heater.
Turn the gas control to off
Only if you can do so without delay and no smell is present.
Call a licensed plumber
Gas work is not a place for trial and error.
What an igniter does
Many newer gas storage heaters use an electronic igniter instead of a standing pilot. When the thermostat calls for heat, the igniter glows or sparks, the gas valve opens and the burner lights. If the igniter is weak or cracked, the burner never lights, and you get no hot water.
Older heaters use a standing pilot light and a thermocouple instead. Which design you have decides which part fails.
Signs the igniter has failed
A heater with a bad igniter usually shows no flame and stays cold. Some models flash a diagnostic light, and the label on the unit explains the code. A clicking sound with no flame, or a glow that never gets bright, also points to the igniter.
Igniter or something else
Several parts can cause the same symptom.
| Symptom | Possible cause | Who handles it |
|---|---|---|
| No flame and no glow | Failed igniter or control board | Licensed plumber |
| Pilot keeps going out | Dirty pilot or bad thermocouple | Licensed plumber |
| Flame starts then dies | Flame sensor or venting problem | Licensed plumber |
| Water too hot or too cold | Thermostat problem | Plumber visit |
| Tank leaking | Corroded tank | See water heater replacement |
Dealing with this right now? Call the line and describe what is happening.
Call (407) 964-8940What you can check safely
You can check that the gas supply valve to the heater is open, that the breaker for any electronic control is on and that the thermostat is set above the water temperature. Look at the label for a diagnostic code. Write down what you see.
Do not remove the burner cover or work on gas connections. That is where a licensed plumber should take over.
Why replacement is not a casual DIY job
Igniters are model specific, and the wrong part can fail or damage the control. Working near a gas valve and a combustion chamber risks leaks and carbon monoxide. A plumber tests for gas leaks and combustion after the repair, which is the step an amateur repair usually skips.
Repair or replace the heater
A heater under ten years old with a bad igniter is usually worth repairing. A heater nearing the end of its life, with rust at the base or a leaking tank, is better replaced. Our water heater repair page and replacement page explain how we weigh the two.
What to tell the plumber
A clear description speeds up the visit.
- The brand and age. The label on the tank lists both.
- The symptom. No flame, a clicking sound or a blinking light.
- What you checked. Gas valve, breaker and thermostat setting.
- Any smell of gas. Say so up front.
What a professional repair includes
A licensed plumber starts by confirming the diagnosis, because an igniter that looks dead may be the symptom of a bad control board or a gas valve problem. They check the gas supply, the venting and the flame sensor before ordering parts, and they test the new igniter under load.
After the repair, the plumber checks for gas leaks at every connection and confirms that combustion is clean. That final step is what separates a real repair from a lucky one, and it is the reason we do not recommend doing gas work yourself.
Keeping the heater healthy afterward
Flush the tank once a year to clear sediment, which insulates the burner area and shortens parts life. Keep the area around the heater clear of boxes and chemicals, and keep the vent free of obstruction. A yearly visit takes minutes and catches a weak igniter before it fails on a cold morning.
Gas service in the Apopka area
Not every Apopka home uses natural gas. Check your gas bill for the utility name, since in much of the area it is the Lake Apopka Natural Gas District, and homes outside the district may use electric heaters or propane. If you smell gas, call that utility or 911.
The City of Apopka runs an online building permit portal, so ask the City of Apopka building division whether a heater replacement needs a permit for your address.
We also take calls from Ocoee and Zellwood when a heater fails.
Standards and sources. Gas water heater work follows the manufacturer's installation instructions and the National Fuel Gas Code (NFPA 54), and plumbing work in Florida falls under the Florida Building Code, Plumbing. We cite these by name and do not quote section numbers from memory, so ask the City of Apopka building division which requirements apply to your address.
Water heater igniter questions from Apopka homeowners
It is not recommended. Gas work carries a risk of leaks and carbon monoxide, and a licensed plumber should handle it.
Look for a standing flame behind a small window. If you see none, you likely have an electronic igniter.
No. It can also be a failed gas valve or a sensor. A plumber tests it.
Call the line. If you smell gas, leave and call your gas utility or 911 first.
Check your bill. In much of the area it is the Lake Apopka Natural Gas District.
Want a plumber to look at it? Call the line and describe what you see.
Call (407) 964-8940